Skip to main content
Journal cover image

The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA)

Publication ,  Journal Article
von Windheim, N; Collinson, DW; Lau, T; Brinson, LC; Gall, K
Published in: Rapid Prototyping Journal
January 1, 2021

Purpose: The purpose of this study is to understand how printing parameters and subsequent annealing impacts porosity and crystallinity of 3D printed polylactic acid (PLA) and how these structural characteristics impact the printed material’s tensile strength in various build directions. Design/methodology/approach: Two experimental studies were used, and samples with a flat vs upright print orientation were compared. The first experiment investigates a scan of printing parameters and annealing times and temperatures above the cold crystallization temperature (Tcc) for PLA. The second experiment investigates annealing above and below Tcc at multiple points over 12 h. Findings: Annealing above Tcc does not significantly impact the porosity but it does increase crystallinity. The increase in crystallinity does not contribute to an increase in strength, suggesting that co-crystallization across the weld does not occur. Atomic force microscopy (AFM) images show that weld interfaces between printed fibers are still visible after annealing above Tcc, confirming the lack of co-crystallization. Annealing below Tcc does not significantly impact porosity or crystallinity. However, there is an increase in tensile strength. AFM images show that annealing below Tcc reduces thermal stresses that form at the interfaces during printing and slightly “heals” the as-printed interface resulting in an increase in tensile strength. Originality/value: While annealing has been explored in the literature, it is unclear how it affects porosity, crystallinity and thermal stresses in fused filament fabrication PLA and how those factors contribute to mechanical properties. This study explains how co-crystallization across weld interfaces is necessary for crystallinity to increase strength and uses AFM as a technique to observe morphology at the weld.

Duke Scholars

Published In

Rapid Prototyping Journal

DOI

ISSN

1355-2546

Publication Date

January 1, 2021

Volume

27

Issue

7

Start / End Page

1327 / 1336

Related Subject Headings

  • Industrial Engineering & Automation
  • 4017 Mechanical engineering
  • 0913 Mechanical Engineering
 

Citation

APA
Chicago
ICMJE
MLA
NLM
von Windheim, N., Collinson, D. W., Lau, T., Brinson, L. C., & Gall, K. (2021). The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA). Rapid Prototyping Journal, 27(7), 1327–1336. https://doi.org/10.1108/RPJ-08-2020-0205
Windheim, N. von, D. W. Collinson, T. Lau, L. C. Brinson, and K. Gall. “The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA).” Rapid Prototyping Journal 27, no. 7 (January 1, 2021): 1327–36. https://doi.org/10.1108/RPJ-08-2020-0205.
von Windheim N, Collinson DW, Lau T, Brinson LC, Gall K. The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA). Rapid Prototyping Journal. 2021 Jan 1;27(7):1327–36.
von Windheim, N., et al. “The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA).” Rapid Prototyping Journal, vol. 27, no. 7, Jan. 2021, pp. 1327–36. Scopus, doi:10.1108/RPJ-08-2020-0205.
von Windheim N, Collinson DW, Lau T, Brinson LC, Gall K. The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA). Rapid Prototyping Journal. 2021 Jan 1;27(7):1327–1336.
Journal cover image

Published In

Rapid Prototyping Journal

DOI

ISSN

1355-2546

Publication Date

January 1, 2021

Volume

27

Issue

7

Start / End Page

1327 / 1336

Related Subject Headings

  • Industrial Engineering & Automation
  • 4017 Mechanical engineering
  • 0913 Mechanical Engineering