Skip to main content
Journal cover image

The digital motion control system for the submillimeter array antennas

Publication ,  Journal Article
Hunter, TR; Wilson, RW; Kimberk, R; Leiker, PS; Patel, NA; Blundell, R; Christensen, RD; Diven, AR; Maute, J; Plante, RJ; Riddle, P; Young, KH
Published in: Journal of Astronomical Instrumentation
September 1, 2013

We describe the design and performance of the digital servo and motion control system for the 6-meter parabolic antennas of the Submillimeter Array (SMA) on Mauna Kea, Hawaii. The system is divided into three nested layers operating at a different, appropriate bandwidth. (1) A rack-mounted, real-time Unix system runs the position loop which reads the high resolution azimuth and elevation encoders and sends velocity and acceleration commands at 100 Hz to a custom-designed servo control board (SCB). (2) The microcontroller-based SCB reads the motor axis tachometers and implements the velocity loop by sending torque commands to the motor amplifiers at 558 Hz. (3) The motor amplifiers implement the torque loop by monitoring and sending current to the three-phase brushless drive motors at 20 kHz. The velocity loop uses a traditional proportional-integral-derivative (PID) control algorithm, while the position loop uses only a proportional term and implements a command shaper based on the Gauss error function. Calibration factors and software filters are applied to the tachometer feedback prior to the application of the servo gains in the torque computations. All of these parameters are remotely adjustable in the software. The three layers of the control system monitor each other and are capable of shutting down the system safely if a failure or anomaly occurs. The Unix system continuously relays the antenna status to the central observatory computer via reflective memory. In each antenna, a Palm Vx hand controller displays the complete system status and allows full local control of the drives in an intuitive touchscreen user interface. The hand controller can also be connected outside the cabin, a major convenience during the frequent reconfigurations of the interferometer. Excellent tracking performance (∼ 0.3′′ rms) is achieved with this system. It has been in reliable operation on 8 antennas for over 10 years and has required minimal maintenance.

Duke Scholars

Published In

Journal of Astronomical Instrumentation

DOI

EISSN

2251-1725

ISSN

2251-1717

Publication Date

September 1, 2013

Volume

2

Issue

1

Related Subject Headings

  • 5101 Astronomical sciences
 

Citation

APA
Chicago
ICMJE
MLA
NLM
Hunter, T. R., Wilson, R. W., Kimberk, R., Leiker, P. S., Patel, N. A., Blundell, R., … Young, K. H. (2013). The digital motion control system for the submillimeter array antennas. Journal of Astronomical Instrumentation, 2(1). https://doi.org/10.1142/S2251171713500025
Hunter, T. R., R. W. Wilson, R. Kimberk, P. S. Leiker, N. A. Patel, R. Blundell, R. D. Christensen, et al. “The digital motion control system for the submillimeter array antennas.” Journal of Astronomical Instrumentation 2, no. 1 (September 1, 2013). https://doi.org/10.1142/S2251171713500025.
Hunter TR, Wilson RW, Kimberk R, Leiker PS, Patel NA, Blundell R, et al. The digital motion control system for the submillimeter array antennas. Journal of Astronomical Instrumentation. 2013 Sep 1;2(1).
Hunter, T. R., et al. “The digital motion control system for the submillimeter array antennas.” Journal of Astronomical Instrumentation, vol. 2, no. 1, Sept. 2013. Scopus, doi:10.1142/S2251171713500025.
Hunter TR, Wilson RW, Kimberk R, Leiker PS, Patel NA, Blundell R, Christensen RD, Diven AR, Maute J, Plante RJ, Riddle P, Young KH. The digital motion control system for the submillimeter array antennas. Journal of Astronomical Instrumentation. 2013 Sep 1;2(1).
Journal cover image

Published In

Journal of Astronomical Instrumentation

DOI

EISSN

2251-1725

ISSN

2251-1717

Publication Date

September 1, 2013

Volume

2

Issue

1

Related Subject Headings

  • 5101 Astronomical sciences